It's hard to see in the picture, due to the color I used, but there will be a ledge all the way around the rails, so the bed will be supported all the way around, in addition to the cross support in the middle.

That ledge will be on top of the ash, so the mattress doesn't rest directly on the part you've seen so far.

Cool. Can't wait to see more.

Bleh. Had an annoying weekend. Enamored with our new toy (the router table), we got cute with the joint attaching those bottom right Rs. As a result, we ended up messing the rails up further (in addition to cutting two of them too short, as mentioned above). The required repairs for that damage mean that we actually moved backwards over the weekend.

I was bummed for a few hours after that.

sorry to hear that, but comforted that I'm not the only one who does stuff like that.

The learning curve is actually a sine wave. The highs and lows will even out, and you'll end up with a beautiful bed.

How right you are. Last weekend went very well. But before I get to that, I'll try to catch up. I've been lazy uploading for a while now.


We made the tops of the corners. Starting with a bit of narrow walnut, we made it a bit narrower with the tablesaw.
http://farm3.static.flickr.com/2189/...9d4ae8744d.jpg


My dad got this miter saw for picture frames, and it works great for this, too.

http://farm3.static.flickr.com/2083/...1ca7622dbe.jpg


I got him these clamps for picture frames years ago, and they've come in very handy.

http://farm3.static.flickr.com/2330/...b50d847cc6.jpg


The joint looks good.

http://farm3.static.flickr.com/2392/...b5d643b2cb.jpg


Clamp and glue the top on. Lots of glue joints in this piece; no way around it, given the look I'm going for.

http://farm3.static.flickr.com/2155/...93936655a7.jpg


The corner with the top, outside and inside.

http://farm3.static.flickr.com/2015/...fe5bc6b7f8.jpg
http://farm3.static.flickr.com/2374/...9983c330aa.jpg

Now for the sliding dovetails. The feet will be made of two boards attached at a right angle in sliding dovetails on the bottom of the corners. The point of that right angle has to cross the line of the diagonal between the two points at which the rails exit the corner.

http://farm3.static.flickr.com/2184/...8045ab2fbb.jpg


The router table makes sliding dovetails possible (OK, feasible). We prepare for the dovetail bit with a straight bit. One with a screw shape may have been better, as the groove left by the bit was hard-packed with sawdust that was difficult to get out, even with a screwdriver.

The clamp on the router table fence is an easy way to stop it at the right point.

http://farm3.static.flickr.com/2108/...4e3e267235.jpg


We moved the clamp to the other side, and cut in the other direction.

http://farm3.static.flickr.com/2184/...de9515f93d.jpg


We then ran the dovetail bit through the same path.

http://farm3.static.flickr.com/2189/...4ea2e0cd3b.jpg

http://farm3.static.flickr.com/2014/...205e566be6.jpg

We ran the dovetail bit along each side of one end of each foot board as well, and voila!

http://farm3.static.flickr.com/2383/...30dc0dc5f8.jpg

OK, I'll try to get more caught up.

The two halves of each foot connect with a lock miter, another product of the router table.

http://farm3.static.flickr.com/2309/...4a3d81a4bd.jpg


I raised the template block on a shim so the bit was centered on the thickness of wood I was using. I'm not 100% certain that that was the best way to do it, but it worked. If I try it again on a more visible joint, I may have to do more experimentation.

Additionally, the bit was too wide for the table insert we had. Maneuvering without an insert was tricky. We have since gotten more inserts.

http://farm3.static.flickr.com/2263/...b1717fe467.jpg


One piece must be cut horizontal:

http://farm3.static.flickr.com/2297/...7c3df296ce.jpg


And the other vertical. This one was trickier. We clamped a strip of wood to the board, and ran that strip along the top of the fence, to keep from falling into the hole left by the lack of an insert.

http://farm3.static.flickr.com/2410/...4e6011cdb9.jpg

All the boards laid flat:

http://farm3.static.flickr.com/2123/...0cc3a71dbb.jpg


And put together. They haven't been cut to final length yet.

http://farm3.static.flickr.com/2165/...4c934dfb13.jpg

Due to the way we did the lap joint, the bottom pieces were not all of a uniform length in each direction. A quick cut against the fence on the tablesaw fixed that.

http://farm3.static.flickr.com/2381/...ecba61b836.jpg



Check out the fit of the feet, and how much extra wood we have on the long board, and how short the short one is.

http://farm3.static.flickr.com/2165/...7de0f2c7ae.jpg


At long last, it's time to glue he bottom into the sides.

http://farm3.static.flickr.com/2394/...690da3d122.jpg


We need a walnut facade on the outer edge of the bottom, as that part will be slightly visible. We cut a notch into the end of a narrow board, and then cut off three and a half inches.

http://farm3.static.flickr.com/2117/...114cc9caf8.jpg


The facade is clamped in place, and a hole is drilled for a dowel. Endgrain isn't good for gluing, so a dowel is needed. A single dowel should be sufficient, as this should not bear any load.

http://farm3.static.flickr.com/2368/...ce5b7f5c6c.jpg


Glue on the facade and hammer in the dowel.

http://farm3.static.flickr.com/2258/...67121b01ee.jpg

Cut off the excess dowel, and plane the joint smooth. We used the tablesaw for this one, but that was too much of a hassle, so my dad planed the rest of them.

http://farm3.static.flickr.com/2289/...6c698d3356.jpg
http://farm3.static.flickr.com/2164/...64c69f5813.jpg

I made a jig to cut all of the feet to a uniform height. The dovetailed end of the board goes up against the block. With boards this short, this is much safer and easier than a fence.

http://farm3.static.flickr.com/2126/...7794250dc8.jpg
http://farm3.static.flickr.com/2128/...6fcf66e429.jpg


All the same height now. One is too short. I'll fix that later.

http://farm3.static.flickr.com/2144/...c26a926d02.jpg

To give the illusion that each corner is a single block of wood, and to avoid nighttime skinned shin injuries, the edges are rounded over, using a half-inch roundover bit.

The roundover bit has a guide on it, so you don't need the fence. However, to reduce chatter when first contacting the bit, there is a post screwed into the router table surface. Holding the piece up against that post when contacting the bit makes it easier to maintain control while waiting to contact the guide.

I did the outside edges first, so the bit would run along the curved surface when doing the top and bottom.

http://farm3.static.flickr.com/2370/...c4ccb452ae.jpg



I then did the bottom, and finally the top.

http://farm3.static.flickr.com/2305/...6152714f64.jpg
http://farm3.static.flickr.com/2289/...c054bfa88e.jpg

I was originally going to round over that corner, but my parents convinced me not to, to add a point of contrast.

Time to finish up the corners, by attaching the feet!

After a bit of sanding, to make the sliding dovetails easier to adjust during gluing, I slid them in place, and added glue to the lock miter joint, taking care to get it in all the nooks and crannies.

http://farm3.static.flickr.com/2204/...8c97357afb.jpg


I (earlier, not pictured) cut off the excess wood from the long feet, and kept one of those pieces to fix the short one, shown here. The extra piece even came pre-dovetailed!

Better safe than sorry- I also added a glue block to the inside of the joint.

http://farm3.static.flickr.com/2368/...e77c0cc1dc.jpg


And, speaking of better safe than sorry, I added a bit of hardware to the rails.

http://farm3.static.flickr.com/2344/...a86cc4642a.jpg

And speaking of the rails, it is time to attach them together. To allow them to be taken apart, they are attached with bolts and cross-dowels.

To help make the bolt holes straight, the initial hole is drilled with the drill press (Sorry for the psychedelics, my camera was set to nighttime mode).

In this picture, you can also see the solutions for the two major mistakes made on the project. The board is capped to make up for cutting it too short, and you can see the wood strip filling the groove we messed up on.

http://farm3.static.flickr.com/2090/...c6bcca33d4.jpg


We held the rails in position with a square on the bottom, and a framing clamp on top.

http://farm3.static.flickr.com/2149/...736e5b9181.jpg


With the boards held in position, and the first part of the hole predrilled, going the rest of the way wasn't too difficult. Out of eight holes, only one got appreciably off course.

http://farm3.static.flickr.com/2154/...a51118fc73.jpg


We then took it apart, and drilled the last bit.

http://farm3.static.flickr.com/2323/...78605f9a10.jpg

I used a square to mark where I hoped the bolt had gone, and drilled down on that line with a bigger bit. For the one that got off course, I had to do this a second time to enlarge that hole.

http://farm3.static.flickr.com/2262/...f9004a08d8.jpg


After the holes are drilled, and the correction made, it goes together.

http://farm3.static.flickr.com/2378/...4fed2aa001.jpg


The bolt heads stick out a bit. The rails have to fit snug in the corners, so the bolts need to be countersunk.

http://farm4.static.flickr.com/3203/...a0d0eecf3a.jpg


Initial holes are cut with a forstner bit.

http://farm3.static.flickr.com/2254/...47b9a8c498.jpg


The bit wasn't quite big enough, so it was finished with a chisel.

http://farm4.static.flickr.com/3264/...7e759b36d9.jpg

Time for staining! My dad made a picture frame with an interesting color that I liked- walnut with an ebony stain.

Initially, it is very black.

http://farm4.static.flickr.com/3260/...a9bf63f177.jpg


After letting it soak, we rubbed off the excess with a rag.

http://farm3.static.flickr.com/2290/...f235d420b5.jpg


The walnut is more visible through the stain as it dries.

http://farm3.static.flickr.com/2398/...67ca7072a4.jpg
http://farm4.static.flickr.com/3059/...3b0b612cb0.jpg


The corners get the same treatment.
http://farm3.static.flickr.com/2106/...108dd1a417.jpg
http://farm4.static.flickr.com/3063/...ea64461bc8.jpg